[flashrom] working: HP Compaq nc6400 laptop
Daniel Challen
daniel.challen at ocsl.co.uk
Wed Dec 9 17:43:18 CET 2009
Hi,
I successfully used flashrom (it was maybe 6 months ago, so I'm
unsure which version of flashrom I used) to upgrade the official BIOS on
an HP laptop (lspci, flashrom etc output attached). This was before I
noticed the warning against flashrom on laptops, so I consider myself
lucky ;)
Thanks for a great tool
- Dan (Norky on irc)
-------------- next part --------------
flashrom v0.9.1-r710
No coreboot table found.
Found chipset "Intel ICH7M", enabling flash write...
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode disabled
0xffe00000/0xffa00000 FWH decode disabled
0xffd80000/0xff980000 FWH decode disabled
0xffd00000/0xff900000 FWH decode disabled
0xffc80000/0xff880000 FWH decode disabled
0xffc00000/0xff800000 FWH decode disabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1
Root Complex Register Block address = 0xfed90000
GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI)
Top Swap : not enabled
SPIBAR = 0xfed90000 + 0x3020
0x00: 0x8004 (SPIS)
0x02: 0x4200 (SPIC)
0x04: 0x00000000 (SPIA)
0x08: 0xc21420c2 (SPID0)
0x0c: 0x00000000 (SPID0+4)
0x10: 0x00000000 (SPID1)
0x14: 0x00000000 (SPID1+4)
0x18: 0x00000000 (SPID2)
0x1c: 0x00000000 (SPID2+4)
0x20: 0x00000000 (SPID3)
0x24: 0x00000000 (SPID3+4)
0x28: 0x00000000 (SPID4)
0x2c: 0x00000000 (SPID4+4)
0x30: 0x00000000 (SPID5)
0x34: 0x00000000 (SPID5+4)
0x38: 0x00000000 (SPID6)
0x3c: 0x00000000 (SPID6+4)
0x40: 0x00000000 (SPID7)
0x44: 0x00000000 (SPID7+4)
0x50: 0x00000000 (BBAR)
0x54: 0x5006 (PREOP)
0x56: 0x7f48 (OPTYPE)
0x58: 0x0405039f (OPMENU)
0x5c: 0x0102d852 (OPMENU+4)
0x60: 0x00000000 (PBR0)
0x64: 0x00000000 (PBR1)
0x68: 0x00000000 (PBR2)
0x6c: 0x00000000 (PBR3)
WARNING: SPI Configuration Lockdown activated.
Generating OPCODES... done
SPI Read Configuration: prefetching disabled, caching enabled, OK.
This chipset supports the following protocols: SPI.
Calibrating delay loop... 512M loops per second, 100 myus = 197 us. OK.
Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29F040B, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ASD AE49F2008, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT29C512, 64 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT29C020, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMIC A25L40P, 512 KB: RDID returned 0xc2 0x20 0x14 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for AMIC A29002B, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMIC A29002T, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMIC A29040B, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for EMST F49B002UA, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Intel 82802AB, 512 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Intel 82802AC, 1024 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Chip status register is 00
Chip status register: Status Register Write Disable (SRWD) is not set
Chip status register: Bit 6 is not set
Chip status register: Bit 5 / Block Protect 3 (BP3) is not set
Chip status register: Bit 4 / Block Protect 2 (BP2) is not set
Chip status register: Bit 3 / Block Protect 1 (BP1) is not set
Chip status register: Bit 2 / Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000.
Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Numonyx M25PE40, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for PMC Pm29F0002T, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for PMC Pm29F0002B, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for PMC Pm49FL002, 256 KB: skipped. Host bus type SPI and chip bus type LPC,FWH are incompatible.
Probing for PMC Pm49FL004, 512 KB: skipped. Host bus type SPI and chip bus type LPC,FWH are incompatible.
Probing for Sharp LHF00L04, 1024 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for SST SST25VF040.REMS, 512 KB: Invalid OPCODE 0x90
Probing for SST SST25VF040B.REMS, 512 KB: Invalid OPCODE 0x90
Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for SST SST28SF040A, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST29EE010, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST29LE010, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST29EE020A, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST29LE020, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39SF010A, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39SF020A, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39SF040, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39VF512, 64 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39VF010, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39VF020, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39VF040, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST39VF080, 1024 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SST SST49LF002A/B, 256 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF003A/B, 384 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF004A/B, 512 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF004C, 512 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF008A, 1024 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF008C, 1024 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF016C, 2048 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for SST SST49LF020, 256 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for SST SST49LF020A, 256 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for SST SST49LF040, 512 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for SST SST49LF040B, 512 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x14. Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x14. Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x14. Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for ST M29F002B, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ST M29F040B, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ST M29F400BT, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ST M29W010B, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ST M29W040B, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for ST M50FLW040A, 512 KB: skipped. Host bus type SPI and chip bus type LPC,FWH are incompatible.
Probing for ST M50FLW040B, 512 KB: skipped. Host bus type SPI and chip bus type LPC,FWH are incompatible.
Probing for ST M50FLW080A, 1024 KB: skipped. Host bus type SPI and chip bus type LPC,FWH are incompatible.
Probing for ST M50FLW080B, 1024 KB: skipped. Host bus type SPI and chip bus type LPC,FWH are incompatible.
Probing for ST M50FW002, 256 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for ST M50FW016, 2048 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for ST M50FW040, 512 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for ST M50FW080, 1024 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for ST M50LPW116, 2048 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Probing for Winbond W29C011, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Winbond W29C020C, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Winbond W29C040P, 512 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Winbond W29EE011, 128 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Winbond W39V040A, 512 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for Winbond W39V040B, 512 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for Winbond W39V040C, 512 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for Winbond W39V040FA, 512 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for Winbond W49F002U, 256 KB: skipped. Host bus type SPI and chip bus type Parallel are incompatible.
Probing for Winbond W49V002A, 256 KB: skipped. Host bus type SPI and chip bus type LPC are incompatible.
Probing for Winbond W49V002FA, 256 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Winbond W39V080FA, 1024 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Winbond W39V080FA (dual mode), 512 KB: skipped. Host bus type SPI and chip bus type FWH are incompatible.
Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x100000000.
RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Not unmapping zero size at (nil)
Probing for EON unknown EON SPI chip, 0 KB: Not mapping flash chip, zero size at 0x100000000.
RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Not unmapping zero size at (nil)
Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x100000000.
RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Not unmapping zero size at (nil)
Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x100000000.
RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Not unmapping zero size at (nil)
Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x100000000.
RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Not unmapping zero size at (nil)
Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x100000000.
RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014
Not unmapping zero size at (nil)
No operations were specified.
-------------- next part --------------
00:00.0 0600: 8086:27a0 (rev 03)
Subsystem: 103c:30ad
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
00:02.0 0300: 8086:27a2 (rev 03) (prog-if 00 [VGA controller])
Subsystem: 103c:30ad
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4600000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 4000 [size=8]
Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f4680000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: i915
Kernel modules: i915
00:02.1 0380: 8086:27a6 (rev 03)
Subsystem: 103c:30ad
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f4700000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30ad
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4780000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 0604: 8086:27d0 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Memory behind bridge: f4100000-f41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 2, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: 103c:30ad
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 0604: 8086:27d2 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
Memory behind bridge: f4000000-f40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 3, PowerLimit 0.160000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: 103c:30ad
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 0604: 8086:27d6 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: f0000000-f3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 4, PowerLimit 0.160000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4181
Capabilities: [90] Subsystem: 103c:30ad
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 0c03: 8086:27c8 (rev 01) (prog-if 00 [UHCI])
Subsystem: 103c:30ad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 4020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 0c03: 8086:27c9 (rev 01) (prog-if 00 [UHCI])
Subsystem: 103c:30ad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 4040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 0c03: 8086:27ca (rev 01) (prog-if 00 [UHCI])
Subsystem: 103c:30ad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 4060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 0c03: 8086:27cb (rev 01) (prog-if 00 [UHCI])
Subsystem: 103c:30ad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 4080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 0c03: 8086:27cc (rev 01) (prog-if 20 [EHCI])
Subsystem: 103c:30ad
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f4784000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 0604: 8086:2448 (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 00005000-00005fff
Memory behind bridge: f4200000-f45fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: 103c:30ad
00:1f.0 0601: 8086:27b9 (rev 01)
Subsystem: 103c:30ad
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 0101: 8086:27df (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: 103c:30ad
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 40a0 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_generic, pata_acpi
00:1f.2 0106: 8086:27c5 (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: 103c:30ad
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Region 0: I/O ports at 13f0 [size=8]
Region 1: I/O ports at 15f4 [size=4]
Region 2: I/O ports at 1370 [size=8]
Region 3: I/O ports at 1574 [size=4]
Region 4: I/O ports at 40d0 [size=16]
Region 5: Memory at f4785000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0200c Data: 4191
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci
02:06.0 0607: 104c:8039
Subsystem: 103c:30ad
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f4200000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: c0000000-c3fff000 (prefetchable)
Memory window 1: c4000000-c7fff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:06.2 0180: 104c:803b
Subsystem: 103c:30ad
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f4201000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: tifm_7xx1
Kernel modules: tifm_7xx1
02:06.3 0805: 104c:803c
Subsystem: 103c:30ad
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 22
Region 0: Memory at f4202000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
02:06.4 0780: 104c:803d
Subsystem: 103c:30ad
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4203000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f4204000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
08:00.0 0200: 14e4:16fd (rev 21)
Subsystem: 103c:30ad
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f4100000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95751M
[EC] Engineering changes: 106679-15
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 34 65 34
[RV] Reserved: checksum bad, 27 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [58] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee0200c Data: 41b1
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [13c] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-16-d4-ff-fe-e6-6a-97
Kernel driver in use: tg3
Kernel modules: tg3
10:00.0 0280: 8086:4222 (rev 02)
Subsystem: 103c:135c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 41a9
Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140] Device Serial Number 00-19-d2-ff-ff-6f-ab-e2
Kernel driver in use: iwl3945
Kernel modules: iwl3945
-------------- next part --------------
# dmidecode 2.10
SMBIOS 2.4 present.
23 structures occupying 1032 bytes.
Table at 0x000F398F.
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Hewlett-Packard
Version: 68YCU Ver. F.0B
Release Date: 09/05/2007
Address: 0xE0000
Runtime Size: 128 kB
ROM Size: 1024 kB
Characteristics:
PCI is supported
PC Card (PCMCIA) is supported
PNP is supported
BIOS is upgradeable
BIOS shadowing is allowed
Boot from CD is supported
Selectable boot is supported
EDD is supported
3.5"/720 kB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
Smart battery is supported
BIOS boot specification is supported
Function key-initiated network boot is supported
Targeted content distribution is supported
BIOS Revision: 15.11
Firmware Revision: 86.52
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Hewlett-Packard
Product Name:
Version: F.0B
Serial Number:
UUID: Not Settable
Wake-up Type: Power Switch
SKU Number:
Family: 103C_5336AN
Handle 0x0040, DMI type 126, 4 bytes
Inactive
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Hewlett-Packard
Product Name: 30AD
Version: KBC Version 56.34
Serial Number: Not Specified
Handle 0x0003, DMI type 3, 13 bytes
Chassis Information
Manufacturer: Hewlett-Packard
Type: Notebook
Lock: Not Present
Version: Not Specified
Serial Number:
Asset Tag:
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: External Interface Enabled
Handle 0x0041, DMI type 126, 4 bytes
Inactive
Handle 0x0004, DMI type 4, 35 bytes
Processor Information
Socket Designation: U10
Type: Central Processor
Family: Pentium M
Manufacturer: Intel(R)
ID: F6 06 00 00 FF FB EB BF
Signature: Type 0, Family 6, Model 15, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz
Voltage: 1.1 V
External Clock: 166 MHz
Max Speed: 1833 MHz
Current Speed: 1833 MHz
Status: Populated, Enabled
Upgrade: None
L1 Cache Handle: 0x0005
L2 Cache Handle: 0x0006
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0005, DMI type 7, 19 bytes
Cache Information
Socket Designation: Internal L1 Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 64 kB
Maximum Size: 64 kB
Supported SRAM Types:
Burst
Installed SRAM Type: Burst
Speed: Unknown
Error Correction Type: Unknown
System Type: Unified
Associativity: 4-way Set-associative
Handle 0x0006, DMI type 7, 19 bytes
Cache Information
Socket Designation: Internal L2 Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: External
Installed Size: 2048 kB
Maximum Size: 2048 kB
Supported SRAM Types:
Burst
Installed SRAM Type: Burst
Speed: Unknown
Error Correction Type: None
System Type: Unified
Associativity: 4-way Set-associative
Handle 0x0007, DMI type 9, 13 bytes
System Slot Information
Designation: PC CARD-Slot 0
Type: 32-bit PC Card (PCMCIA)
Current Usage: Available
Length: Short
ID: Adapter 0, Socket 0
Characteristics:
5.0 V is provided
3.3 V is provided
PC Card-16 is supported
Cardbus is supported
PME signal is supported
Handle 0x0008, DMI type 10, 6 bytes
On Board Device Information
Type: Video
Status: Enabled
Description: 8
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: www.hp.com
String 2: ABS 70/71 79 7A 7B 7C 7D
Handle 0x000A, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 4 GB
Error Information Handle: No Error
Number Of Devices: 2
Handle 0x000B, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: SODIMM
Set: None
Locator: DIMM #1
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Manufacturer: 7F7F7F1600000000
Serial Number: 00000000
Asset Tag: Not Specified
Part Number: NL8126426407F-D53M
Handle 0x000C, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x000A
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: SODIMM
Set: None
Locator: DIMM #2
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 975 MHz
Manufacturer: AD00000000000000
Serial Number: 00002003
Asset Tag: Not Specified
Part Number: HYMP125S64CP8-S6
Handle 0x000D, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000BFFFFFFF
Range Size: 3 GB
Physical Array Handle: 0x000A
Partition Width: 0
Handle 0x000E, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0003FFFFFFF
Range Size: 1 GB
Physical Device Handle: 0x000B
Memory Array Mapped Address Handle: 0x000D
Partition Row Position: 1
Handle 0x000F, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00040000000
Ending Address: 0x000BFFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x000C
Memory Array Mapped Address Handle: 0x000D
Partition Row Position: 2
Handle 0x0010, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x0085, DMI type 133, 34 bytes
OEM-specific Type
Header and Data:
85 22 85 00 01 EC 13 BE 10 BE 10 04 00 49 00 17
00 F6 30 00 00 30 2A 02 E0 40 00 00 52 10 50 10
55 10
Strings:
01824 03/17/2007
HP
Handle 0x0086, DMI type 126, 34 bytes
Inactive
Handle 0x0011, DMI type 144, 26 bytes
OEM-specific Type
Header and Data:
90 1A 11 00 FF FF FF FF FF FF FF FF FF FF FF FF
FF FF FF FF FF FF FF FF 00 00
Handle 0x0012, DMI type 127, 4 bytes
End Of Table
More information about the flashrom
mailing list