[flashrom] succesful flash write on Supermicro X8DTT-F
Taylan Develioglu
tdevelioglu at ebuddy.com
Tue Mar 23 13:29:37 CET 2010
Succesfully perfomed flashrom -w on the SM X8DTT-F, requested details
are attached.
Official BIOS downloads are from:
http://www.supermicro.com/support/bios/
-------------- next part --------------
superiotool r5263
Probing for ALi Super I/O at 0x3f0...
Failed. Returned data: id=0xffff, rev=0xff
Probing for ALi Super I/O at 0x370...
Failed. Returned data: id=0xffff, rev=0xff
Probing for Fintek Super I/O at 0x2e...
Failed. Returned data: vid=0x4000, id=0x73b0
Probing for Fintek Super I/O at 0x4e...
Failed. Returned data: vid=0x0000, id=0x111a
Probing for ITE Super I/O (init=standard) at 0x2e...
Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x2e...
Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x2e...
Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x2e...
Failed. Returned data: id=0xb073, rev=0xf
Probing for ITE Super I/O (init=standard) at 0x4e...
Failed. Returned data: id=0x1a11, rev=0x0
Probing for ITE Super I/O (init=it8761e) at 0x4e...
Failed. Returned data: id=0x1a11, rev=0x0
Probing for ITE Super I/O (init=it8228e) at 0x4e...
Failed. Returned data: id=0x1a11, rev=0x0
Probing for ITE Super I/O (init=0x87,0x87) at 0x4e...
Failed. Returned data: id=0x1a11, rev=0x0
Probing for ITE Super I/O (init=legacy/it8661f) at 0x370...
Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8671f) at 0x370...
Failed. Returned data: id=0xffff, rev=0xf
Probing for NSC Super I/O at 0x2e...
Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x4e...
Failed. Returned data: sid=0x1a, srid=0x00
Probing for NSC Super I/O at 0x15c...
Failed. Returned data: port=0xff, port+1=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e...
Failed. Returned data: id=0x1a, rev=0x11
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e...
Failed. Returned data: id=0x00, rev=0x00
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370...
Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370...
Failed. Returned data: id=0xff, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x2e...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x2e...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e...
Failed. Returned data: id/oldid=0xb0/0x0f, rev=0x73
Probing for Winbond Super I/O (init=0x88) at 0x4e...
Failed. Returned data: id/oldid=0x1a/0x00, rev=0x11
Probing for Winbond Super I/O (init=0x89) at 0x4e...
Failed. Returned data: id/oldid=0x1a/0x00, rev=0x11
Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...
Failed. Returned data: id/oldid=0x1a/0x00, rev=0x11
Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...
Failed. Returned data: id/oldid=0x1a/0x00, rev=0x11
Probing for Winbond Super I/O (init=0x88) at 0x3f0...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x3f0...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x370...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x370...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x250...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x250...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...
Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for VIA Super I/O at 0x3f0...
PCI device 1106:0686 not found.
No Super I/O found
-------------- next part --------------
flashrom v0.9.1-r971
No coreboot table found.
DMI string system-manufacturer: "Supermicro"
DMI string system-product-name: "X8DTT"
DMI string system-version: "1234567890"
DMI string baseboard-manufacturer: "Supermicro"
DMI string baseboard-product-name: "X8DTT"
DMI string baseboard-version: "1.00 "
DMI string chassis-type: "Main Server Chassis"
Found chipset "Intel ICH10R", enabling flash write...
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x100000 bytes
BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1
Root Complex Register Block address = 0xfed1c000
GCS = 0x60: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x0 (reserved)
Top Swap : not enabled
SPIBAR = 0xfed1c000 + 0x3800
0x04: 0x2008 (HSFS)
FLOCKDN 0, FDV 0, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0
0x50: 0x00000202 (FRAP)
BMWAG 0, BMRAG 0, BRWA 2, BRRA 2
0x54: 0x00001fff (FREG0)
0x58: 0x00001fff (FREG1)
0x5C: 0x00001fff (FREG2)
0x60: 0x00001fff (FREG3)
0x64: 0x00001fff (FREG4)
0x74: 0x00000000 (PR0)
0x78: 0x00000000 (PR1)
0x7C: 0x00000000 (PR2)
0x80: 0x00000000 (PR3)
0x84: 0x00000000 (PR4)
0x90: 0x00414004 (SSFS, SSFC)
0x94: 0x5006 (PREOP)
0x96: 0x463b (OPTYPE)
0x98: 0x05d80302 (OPMENU)
0x9C: 0xc79f0190 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xB0: 0x00000000 (FDOC)
Programming OPCODES...
program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190
done
SPI Read Configuration: prefetching disabled, caching enabled, OK.
This chipset supports the following protocols: FWH,SPI.
Calibrating delay loop... 643M loops per second, 100 myus = 199 us. OK.
Probing for AMD Am29F010A/B, 128 KB: skipped.
Probing for AMD Am29F002(N)BB, 256 KB: skipped.
Probing for AMD Am29F002(N)BT, 256 KB: skipped.
Probing for AMD Am29F016D, 2048 KB: skipped.
Probing for AMD Am29F040B, 512 KB: skipped.
Probing for AMD Am29F080B, 1024 KB: skipped.
Probing for AMD Am29LV040B, 512 KB: skipped.
Probing for AMD Am29LV081B, 1024 KB: skipped.
Probing for ASD AE49F2008, 256 KB: skipped.
Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT29C512, 64 KB: skipped.
Probing for Atmel AT29C010A, 128 KB: skipped.
Probing for Atmel AT29C020, 256 KB: skipped.
Probing for Atmel AT29C040A, 512 KB: skipped.
Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Atmel AT49BV512, 64 KB: skipped.
Probing for Atmel AT49F002(N), 256 KB: skipped.
Probing for Atmel AT49F002(N)T, 256 KB: skipped.
Probing for AMIC A25L40PT, 512 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for AMIC A25L40PU, 512 KB: RDID returned 0xc2 0x20 0x16 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for AMIC A29002B, 256 KB: skipped.
Probing for AMIC A29002T, 256 KB: skipped.
Probing for AMIC A29040B, 512 KB: skipped.
Probing for AMIC A49LF040A, 512 KB: skipped.
Probing for EMST F49B002UA, 256 KB: skipped.
Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B05T, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B10T, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B20T, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B40T, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B80T, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B16T, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B32T, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25B64T, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Eon EN29F010, 128 KB: skipped.
Probing for EON EN29F002(A)(N)B, 256 KB: skipped.
Probing for EON EN29F002(A)(N)T, 256 KB: skipped.
Probing for Fujitsu MBM29F004BC, 512 KB: skipped.
Probing for Fujitsu MBM29F004TC, 512 KB: skipped.
Probing for Fujitsu MBM29F400BC, 512 KB: skipped.
Probing for Fujitsu MBM29F400TC, 512 KB: skipped.
Probing for Intel 28F001BX-B, 128 KB: skipped.
Probing for Intel 28F001BX-T, 128 KB: skipped.
Probing for Intel 28F004S5, 512 KB: skipped.
Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Chip status register is 00
Chip status register: Status Register Write Disable (SRWD) is not set
Chip status register: Bit 6 is not set
Chip status register: Bit 5 / Block Protect 3 (BP3) is not set
Chip status register: Bit 4 / Block Protect 2 (BP2) is not set
Chip status register: Bit 3 / Block Protect 1 (BP1) is not set
Chip status register: Bit 2 / Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
Found chip "Macronix MX25L3205" (4096 KB, SPI) at physical address 0xffc00000.
Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Macronix MX29F001B, 128 KB: skipped.
Probing for Macronix MX29F001T, 128 KB: skipped.
Probing for Macronix MX29F002B, 256 KB: skipped.
Probing for Macronix MX29F002T, 256 KB: skipped.
Probing for Macronix MX29LV040, 512 KB: skipped.
Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Numonyx M25PE40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for PMC Pm29F002T, 256 KB: skipped.
Probing for PMC Pm29F002B, 256 KB: skipped.
Probing for PMC Pm39LV010, 128 KB: skipped.
Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Spansion S25FL008A, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for SST SST25VF040.REMS, 512 KB: REMS returned c2 15. probe_spi_rems: id1 0xc2, id2 0x15
Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for SST SST25VF040B.REMS, 512 KB: REMS returned c2 15. probe_spi_rems: id1 0xc2, id2 0x15
Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for SST SST28SF040A, 512 KB: skipped.
Probing for SST SST29EE010, 128 KB: skipped.
Probing for SST SST29LE010, 128 KB: skipped.
Probing for SST SST29EE020A, 256 KB: skipped.
Probing for SST SST29LE020, 256 KB: skipped.
Probing for SST SST39SF512, 64 KB: skipped.
Probing for SST SST39SF010A, 128 KB: skipped.
Probing for SST SST39SF020A, 256 KB: skipped.
Probing for SST SST39SF040, 512 KB: skipped.
Probing for SST SST39VF512, 64 KB: skipped.
Probing for SST SST39VF010, 128 KB: skipped.
Probing for SST SST39VF020, 256 KB: skipped.
Probing for SST SST39VF040, 512 KB: skipped.
Probing for SST SST39VF080, 1024 KB: skipped.
Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF020, 256 KB: skipped.
Probing for SST SST49LF020A, 256 KB: skipped.
Probing for SST SST49LF040, 512 KB: skipped.
Probing for SST SST49LF040B, 512 KB: skipped.
Probing for SST SST49LF080A, 1024 KB: skipped.
Probing for SST SST49LF160C, 2048 KB: skipped.
Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x16. Ignoring RES in favour of RDID.
Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x16. Ignoring RES in favour of RDID.
Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x16. Ignoring RES in favour of RDID.
Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for ST M29F002B, 256 KB: skipped.
Probing for ST M29F002T/NT, 256 KB: skipped.
Probing for ST M29F040B, 512 KB: skipped.
Probing for ST M29F400BT, 512 KB: skipped.
Probing for ST M29W010B, 128 KB: skipped.
Probing for ST M29W040B, 512 KB: skipped.
Probing for ST M29W512B, 64 KB: skipped.
Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50LPW116, 2048 KB: skipped.
Probing for SyncMOS S29C31004T, 512 KB: skipped.
Probing for SyncMOS S29C51001T, 128 KB: skipped.
Probing for SyncMOS S29C51002T, 256 KB: skipped.
Probing for SyncMOS S29C51004T, 512 KB: skipped.
Probing for TI TMS29F002RB, 256 KB: skipped.
Probing for TI TMS29F002RT, 256 KB: skipped.
Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W25x32, 4096 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W25x64, 8192 KB: RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Probing for Winbond W29C011, 128 KB: skipped.
Probing for Winbond W29C020C, 256 KB: skipped.
Probing for Winbond W29C040P, 512 KB: skipped.
Probing for Winbond W29EE011, 128 KB: skipped.
Probing for Winbond W39V040A, 512 KB: skipped.
Probing for Winbond W39V040B, 512 KB: skipped.
Probing for Winbond W39V040C, 512 KB: skipped.
Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080A, 1024 KB: skipped.
Probing for Winbond W49F002U, 256 KB: skipped.
Probing for Winbond W49V002A, 256 KB: skipped.
Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for EON unknown EON SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000.
RDID returned 0xc2 0x20 0x16. probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Not unmapping zero size at (nil)
Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000.
REMS returned c2 15. probe_spi_rems: id1 0xc2, id2 0x15
Not unmapping zero size at (nil)
===
This flash part has status UNTESTED for operations: ERASE
Please email a report to flashrom at flashrom.org if any of the above operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -rV,
-wV, -EV), and mention which mainboard or programmer you tested.
Thanks for your help!
===
No operations were specified.
-------------- next part --------------
00:00.0 Host bridge: Intel Corporation QuickPath Architecture I/O Hub to ESI Port (rev 13)
Subsystem: Intel Corporation Device 0000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable-
Address: 00000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
00:01.0 PCI bridge: Intel Corporation QuickPath Architecture I/O Hub PCI Express Root Port 1 (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: faf00000-faffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Intel Corporation Device 0000
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 4049
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
Kernel driver in use: pcieport-driver
00:03.0 PCI bridge: Intel Corporation QuickPath Architecture I/O Hub PCI Express Root Port 3 (rev 13) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Intel Corporation Device 0000
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 4051
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
Kernel driver in use: pcieport-driver
00:07.0 PCI bridge: Intel Corporation QuickPath Architecture I/O Hub PCI Express Root Port 7 (rev 13) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Intel Corporation Device 0000
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 4059
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 1, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
Kernel driver in use: pcieport-driver
00:14.0 PIC: Intel Corporation QuickPath Architecture I/O Hub System Management Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
00:14.1 PIC: Intel Corporation QuickPath Architecture I/O Hub GPIO and Scratch Pad Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
00:14.2 PIC: Intel Corporation QuickPath Architecture I/O Hub Control Status and RAS Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
00:14.3 PIC: Intel Corporation QuickPath Architecture I/O Hub Throttle Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:16.0 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at faedc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.1 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at faee0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.2 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at faee4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.3 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at faee8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.4 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at faeec000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.5 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at faef0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.6 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at faef4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.7 System peripheral: Intel Corporation DMA Engine (rev 13)
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at faef8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at bc00 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at c000 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at faefc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at b400 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b480 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b800 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at faeda000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Memory behind bridge: fb000000-fbefffff
Prefetchable memory behind bridge: 00000000f9000000-00000000f9ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Super Micro Computer Inc Device 0007
00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at d880 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d480 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: I/O ports at d080 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ata_piix
Kernel modules: pata_acpi, ata_generic, ata_piix
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 10
Region 0: Memory at faefe000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c880 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at c480 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: I/O ports at c080 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ata_piix
Kernel modules: pata_acpi, ata_generic, ata_piix
01:00.0 Ethernet controller: Intel Corporation Device 10c9 (rev 01)
Subsystem: Super Micro Computer Inc Device 10c9
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at faf60000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at faf40000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e880 [size=32]
Region 3: Memory at faf98000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at faf20000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable+ Mask- TabSize=10
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <4us, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number 18-1f-f0-ff-ff-48-30-00
Capabilities: [150] #0e
Capabilities: [160] #10
Kernel driver in use: igb
Kernel modules: igb
01:00.1 Ethernet controller: Intel Corporation Device 10c9 (rev 01)
Subsystem: Super Micro Computer Inc Device 10c9
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fafe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fafc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=32]
Region 3: Memory at faf9c000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at fafa0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable+ Mask- TabSize=10
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <4us, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number 18-1f-f0-ff-ff-48-30-00
Capabilities: [150] #0e
Capabilities: [160] #10
Kernel driver in use: igb
Kernel modules: igb
04:01.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200eW WPCM450 [Hermon] - Winbond/Nuvoton (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc Device 0007
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f9000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fbefc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=8M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
More information about the flashrom
mailing list