bash-3.2# ./flashrom -EV flashrom v0.9.1-r884 Mapping low megabyte, 0x100000 bytes at unaligned 0x00000400. No coreboot table found. sh: dmidecode: command not found DMI pipe close error Found chipset "Intel ICH10R", enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1 Root Complex Register Block address = 0xfed1c000 GCS = 0x460: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x2008 (HSFS) FLOCKDN 0, FDV 0, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x00000202 (FRAP) BMWAG 0, BMRAG 0, BRWA 2, BRRA 2 0x54: 0x00001fff (FREG0) 0x58: 0x00001fff (FREG1) 0x5C: 0x00001fff (FREG2) 0x60: 0x00001fff (FREG3) 0x64: 0x00001fff (FREG4) 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0x007f1004 (SSFS, SSFC) 0x94: 0x0006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00000000 (FDOC) Programming OPCODES... program_opcodes: preop=0006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Calibrating delay loop... 837M loops per second, 100 myus = 200 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25F512B, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25FS010, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT25FS040, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF041, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT26F004, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT29C512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A25L40PT, 512 KB: RDID returned 0xbf 0x25 0x4a 0xbf. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A25L40PU, 512 KB: RDID returned 0xbf 0x25 0x4a 0xbf. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for AMIC A29002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for EMST F49B002UA, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B05T, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B10, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B10T, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B20, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B20T, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B40, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B40T, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B80, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B80T, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B16, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B16T, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B32, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B32T, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B64, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25B64T, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25D16, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F05, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F10, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F20, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F40, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F80, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F16, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Eon EN25F32, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1005, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L2005, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L4005, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE20, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE40, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV010, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV020, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV040, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm25LV512, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Sharp LHF00L04, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for Spansion S25FL008A, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25VF016B, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25VF032B, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Chip status register is 1c Chip status register: Block Protect Write Disable (BPL) is not set Chip status register: Auto Address Increment Programming (AAI) is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is set Chip status register: Bit 3 / Block Protect 1 (BP1) is set Chip status register: Bit 2 / Block Protect 0 (BP0) is set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "SST SST25VF032B" (4096 KB, SPI) at physical address 0xffc00000. Probing for SST SST25VF040.REMS, 512 KB: REMS returned bf 4a. probe_spi_rems: id1 0xbf, id2 0x4a Probing for SST SST25VF040B, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST25VF040B.REMS, 512 KB: REMS returned bf 4a. probe_spi_rems: id1 0xbf, id2 0x4a Probing for SST SST25VF080B, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST SST28SF040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_49lfxxxc: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF020A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SST SST49LF160C, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for ST M25P05-A, 64 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P05.RES, 64 KB: RDID returned 0xbf 0x25 0x4a. Probing for ST M25P10-A, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P10.RES, 128 KB: RDID returned 0xbf 0x25 0x4a. Probing for ST M25P20, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P40, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P40-old, 512 KB: RDID returned 0xbf 0x25 0x4a. Probing for ST M25P80, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P16, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P32, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P64, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M25P128, 16384 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST M29F002B, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xff, id2 0xff Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x20, 256 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x40, 512 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x80, 1024 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x16, 2048 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x32, 4096 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W25x64, 8192 KB: RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Winbond W29C011, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040B, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040C, 512 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49F002U, 256 KB: skipped. Host bus type FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: skipped. Host bus type FWH,SPI and chip bus type LPC are incompatible. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for EON unknown EON SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xbf 0x25 0x4a. probe_spi_rdid_generic: id1 0xbf, id2 0x254a Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. REMS returned bf 4a. probe_spi_rems: id1 0xbf, id2 0x4a === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! === Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, Invalid OPCODE 0x06 spi_block_erase_20 failed during command execution at address 0x0 Looking at blockwise erase function 1... trying... 0x000000-0x007fff, Invalid OPCODE 0x06 spi_block_erase_52 failed during command execution at address 0x0 Looking at blockwise erase function 2... trying... 0x000000-0x00ffff, 0x010000-0x01ffff, 0x020000-0x02ffff, 0x030000-0x03ffff, 0x040000-0x04ffff, 0x050000-0x05ffff, 0x060000-0x06ffff, 0x070000-0x07ffff, 0x080000-0x08ffff, 0x090000-0x09ffff, 0x0a0000-0x0affff, 0x0b0000-0x0bffff, 0x0c0000-0x0cffff, 0x0d0000-0x0dffff, 0x0e0000-0x0effff, 0x0f0000-0x0fffff, 0x100000-0x10ffff, 0x110000-0x11ffff, 0x120000-0x12ffff, 0x130000-0x13ffff, 0x140000-0x14ffff, 0x150000-0x15ffff, 0x160000-0x16ffff, 0x170000-0x17ffff, 0x180000-0x18ffff, 0x190000-0x19ffff, 0x1a0000-0x1affff, 0x1b0000-0x1bffff, 0x1c0000-0x1cffff, 0x1d0000-0x1dffff, 0x1e0000-0x1effff, 0x1f0000-0x1fffff, 0x200000-0x20ffff, 0x210000-0x21ffff, 0x220000-0x22ffff, 0x230000-0x23ffff, 0x240000-0x24ffff, 0x250000-0x25ffff, 0x260000-0x26ffff, 0x270000-0x27ffff, 0x280000-0x28ffff, 0x290000-0x29ffff, 0x2a0000-0x2affff, 0x2b0000-0x2bffff, 0x2c0000-0x2cffff, 0x2d0000-0x2dffff, 0x2e0000-0x2effff, 0x2f0000-0x2fffff, 0x300000-0x30ffff, 0x310000-0x31ffff, 0x320000-0x32ffff, 0x330000-0x33ffff, 0x340000-0x34ffff, 0x350000-0x35ffff, 0x360000-0x36ffff, 0x370000-0x37ffff, 0x380000-0x38ffff, 0x390000-0x39ffff, 0x3a0000-0x3affff, 0x3b0000-0x3bffff, 0x3c0000-0x3cffff, 0x3d0000-0x3dffff, 0x3e0000-0x3effff, 0x3f0000-0x3fffff, SUCCESS. bash-3.2#