<pre>Hi, I have a laptop with sis chipset and i decided to give you some information about it if it would help.<br>Below are the outputs from lspci, flashrom and superiotool. It seem it hasn't any significant information (except being unsupported).<br>
I hope this helps.<br>Regards,<br>Bugra<br><br>lspci -nnvvvxxx<br></pre><br>00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 671MX [1039:0671]<br> Subsystem: Fujitsu Siemens Computers Device [1734:1125] <br>
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-<br> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-<br>
Latency: 32 <br> Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64M] <br>
Capabilities: <access denied> <br> Kernel driver in use: agpgart-sis <br>
00: 39 10 71 06 07 00 10 22 00 00 00 06 00 20 00 00 <br>10: 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 <br>
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25 11 <br>30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 <br>
<br>00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] SiS AGP Port (virtual PCI-to-PCI bridge) [1039:0003] (prog-if 00 [Normal decode])<br> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br>
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br> Latency: 0, Cache Line Size: 16 bytes <br>
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 <br> I/O behind bridge: 00009000-00009fff <br>
Memory behind bridge: d4000000-d40fffff <br> Prefetchable memory behind bridge: c0000000-cfffffff <br>
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- <br> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- <br>
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- <br> Kernel modules: shpchp <br>
00: 39 10 03 00 07 00 20 00 00 00 04 06 04 00 01 00 <br>10: 00 00 00 00 00 00 00 00 00 01 01 00 90 90 20 20 <br>
20: 00 d4 00 d4 00 c0 f0 cf 00 00 00 00 00 00 00 00 <br>30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 0c 00 <br>
<br>00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] [1039:0968] (rev 01)<br> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-<br>
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-<br> Latency: 0 <br>
00: 39 10 68 09 0f 00 00 02 01 00 01 06 00 00 80 00 <br>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <br>
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <br>30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <br>
<br>00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE] [1039:5513] (rev 01) (prog-if 80 [Master])<br> Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step) [1039:5513] <br>
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br>
Latency: 128 <br> Interrupt: pin ? routed to IRQ 16 <br>
Region 0: I/O ports at 01f0 [size=8] <br> Region 1: I/O ports at 03f4 [size=1] <br>
Region 2: I/O ports at 0170 [size=8] <br> Region 3: I/O ports at 0374 [size=1] <br>
Region 4: I/O ports at 1000 [size=16] <br> Capabilities: <access denied> <br>
Kernel driver in use: pata_sis <br> Kernel modules: pata_sis <br>
00: 39 10 13 55 05 00 10 02 01 80 01 01 00 80 00 00 <br>10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 <br>
20: 01 10 00 00 00 00 00 00 00 00 00 00 39 10 13 55 <br>30: 00 00 00 00 58 00 00 00 00 00 00 00 00 00 00 00 <br>
<br>00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])<br> Subsystem: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] <br>
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br>
Latency: 32 (20000ns max) <br> Interrupt: pin A routed to IRQ 20 <br>
Region 0: Memory at d4204000 (32-bit, non-prefetchable) [size=4K] <br> Kernel driver in use: ohci_hcd <br>
00: 39 10 01 70 17 00 80 02 0f 10 03 0c 00 20 80 00 <br>10: 00 40 20 d4 00 00 00 00 00 00 00 00 00 00 00 00 <br>
20: 00 00 00 00 00 00 00 00 00 00 00 00 39 10 01 70 <br>30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 50 <br>
<br>00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])<br> Subsystem: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] <br>
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br>
Latency: 32 (20000ns max) <br> Interrupt: pin B routed to IRQ 21 <br>
Region 0: Memory at d4205000 (32-bit, non-prefetchable) [size=4K] <br> Kernel driver in use: ohci_hcd <br>
00: 39 10 01 70 17 00 80 02 0f 10 03 0c 00 20 00 00 <br>10: 00 50 20 d4 00 00 00 00 00 00 00 00 00 00 00 00 <br>
20: 00 00 00 00 00 00 00 00 00 00 00 00 39 10 01 70 <br>30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 50 <br>
<br>00:03.3 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0 Controller [1039:7002] (prog-if 20 [EHCI])<br> Subsystem: Fujitsu Siemens Computers Device [1734:1125] <br>
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br>
Latency: 32 (20000ns max), Cache Line Size: 32 bytes <br> Interrupt: pin C routed to IRQ 22 <br>
Region 0: Memory at d4206000 (32-bit, non-prefetchable) [size=4K] <br> Capabilities: <access denied> <br>
Kernel driver in use: ehci_hcd <br>00: 39 10 02 70 06 00 90 02 00 20 03 0c 08 20 00 00 <br>
10: 00 60 20 d4 00 00 00 00 00 00 00 00 00 00 00 00 <br>20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25 11 <br>
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 03 00 50 <br><br>00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02)<br>
Subsystem: Fujitsu Siemens Computers Device [1734:1125] <br> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br>
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br> Latency: 0 <br>
Interrupt: pin A routed to IRQ 19 <br> Region 0: Memory at d4407000 (32-bit, non-prefetchable) [size=128] <br>
Region 1: I/O ports at 1080 [size=128] <br> Capabilities: <access denied> <br>
Kernel driver in use: sis190 <br> Kernel modules: sis190 <br>
00: 39 10 91 01 07 00 10 02 02 00 00 02 00 00 00 00 <br>10: 00 70 40 d4 81 10 00 00 00 00 00 00 00 00 00 00 <br>
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25 11 <br>30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 00 00 <br>
<br>00:05.0 IDE interface [0101]: Silicon Integrated Systems [SiS] SATA Controller / IDE mode [1039:1183] (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])<br> Subsystem: Silicon Integrated Systems [SiS] SATA Controller / IDE mode [1039:1183] <br>
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br>
Latency: 32 <br> Interrupt: pin A routed to IRQ 17 <br>
Region 0: I/O ports at 1058 [size=8] <br> Region 1: I/O ports at 104c [size=4] <br>
Region 2: I/O ports at 1050 [size=8] <br> Region 3: I/O ports at 1048 [size=4] <br>
Region 4: I/O ports at 1020 [size=16] <br> Capabilities: <access denied> <br>
Kernel driver in use: sata_sis <br> Kernel modules: sata_sis <br>
00: 39 10 83 11 05 00 10 02 03 8f 01 01 00 20 00 00 <br>10: 59 10 00 00 4d 10 00 00 51 10 00 00 49 10 00 00 <br>
20: 21 10 00 00 00 00 00 00 00 00 00 00 39 10 83 11 <br>30: 00 00 00 00 58 00 00 00 00 00 00 00 05 01 00 00 <br>
<br>00:06.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:000a] (prog-if 00 [Normal decode])<br> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br>
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br> Latency: 0, Cache Line Size: 16 bytes <br>
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 <br> I/O behind bridge: 0000f000-00000fff <br>
Memory behind bridge: d4100000-d41fffff <br> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff <br>
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- <br> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- <br>
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- <br> Capabilities: <access denied> <br>
Kernel driver in use: pcieport-driver <br> Kernel modules: shpchp <br>
00: 39 10 0a 00 07 00 10 00 00 00 04 06 04 00 01 00 <br>10: 00 00 00 00 00 00 00 00 00 02 02 00 f1 01 00 20 <br>
20: 10 d4 10 d4 f1 ff 01 00 00 00 00 00 00 00 00 00 <br>30: 00 00 00 00 b0 00 00 00 00 00 00 00 09 01 04 00 <br>
<br>00:07.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:000a] (prog-if 00 [Normal decode])<br> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br>
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br> Latency: 0, Cache Line Size: 16 bytes <br>
Bus: primary=00, secondary=4d, subordinate=4e, sec-latency=0 <br> I/O behind bridge: 00003000-00004fff <br>
Memory behind bridge: dc000000-dfffffff <br> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff <br>
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- <br> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- <br>
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- <br> Capabilities: <access denied> <br>
Kernel driver in use: pcieport-driver <br> Kernel modules: shpchp <br>
00: 39 10 0a 00 07 00 10 00 00 00 04 06 04 00 01 00 <br>10: 00 00 00 00 00 00 00 00 00 4d 4e 00 31 41 00 00 <br>
20: 00 dc f0 df f1 ff 01 00 00 00 00 00 00 00 00 00 <br>30: 00 00 00 00 b0 00 00 00 00 00 00 00 09 01 04 00 <br>
<br>00:0f.0 Audio device [0403]: Silicon Integrated Systems [SiS] Azalia Audio Controller [1039:7502]<br> Subsystem: Fujitsu Siemens Computers Device [1734:1125] <br> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-<br>
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-<br> Latency: 0 (13000ns min, 2750ns max) <br>
Interrupt: pin A routed to IRQ 18 <br> Region 0: Memory at d4200000 (32-bit, non-prefetchable) [size=16K] <br>
Capabilities: <access denied> <br> Kernel driver in use: HDA Intel <br>
Kernel modules: snd-hda-intel <br>00: 39 10 02 75 06 00 10 02 00 00 03 04 00 00 00 00 <br>
10: 00 00 20 d4 00 00 00 00 00 00 00 00 00 00 00 00 <br>20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25 11 <br>
30: 00 00 00 00 50 00 00 00 00 00 00 00 04 01 34 0b <br><br>00:1f.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:0004] (prog-if 00 [Normal decode])<br>
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- <br> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- <br>
Latency: 0, Cache Line Size: 16 bytes <br> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 <br>
I/O behind bridge: 0000f000-00000fff <br> Memory behind bridge: fff00000-000fffff <br>
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff <br> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- <br>
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- <br> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- <br>
Capabilities: <access denied> <br> Kernel modules: shpchp <br>
00: 39 10 04 00 07 00 10 00 00 00 04 06 04 00 01 00 <br>10: 00 00 00 00 00 00 00 00 00 04 04 00 f1 01 00 20 <br>
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 <br>30: 00 00 00 00 d0 00 00 00 00 00 00 00 ff 00 04 00<br><br>01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter [1039:6351] (rev 10) (prog-if 00 [VGA controller])<br>
Subsystem: Fujitsu Siemens Computers Device [1734:1125]<br> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-<br> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-<br>
Interrupt: pin A routed to IRQ 16<br> BIST result: 00<br> Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]<br> Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=128K]<br>
Region 2: I/O ports at 9000 [size=128]<br> Expansion ROM at <unassigned> [disabled]<br> Capabilities: <access denied><br>00: 39 10 51 63 03 00 30 02 10 00 00 03 00 00 00 80<br>10: 08 00 00 c0 00 00 00 d4 01 90 00 00 00 00 00 00<br>
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25 11<br>30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 00 00<br><br>02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)<br>
Subsystem: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) [168c:3067]<br> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-<br>
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-<br> Latency: 0, Cache Line Size: 16 bytes<br> Interrupt: pin A routed to IRQ 16<br>
Region 0: Memory at d4100000 (64-bit, non-prefetchable) [size=64K]<br> Capabilities: <access denied><br> Kernel driver in use: ath_pci<br> Kernel modules: ath_pci, ath5k<br>00: 8c 16 1c 00 07 00 10 00 01 00 00 02 04 00 00 00<br>
10: 04 00 10 d4 00 00 00 00 00 00 00 00 00 00 00 00<br>20: 00 00 00 00 00 00 00 00 01 50 00 00 8c 16 67 30<br>30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 00 00<br><br><br>--------------------------------------------------------------<br>
<br>flashrom -V<br>flashrom v0.9.1-r710 <br>No coreboot table found. <br>
This chipset supports the following protocols: Non-SPI. <br>WARNING: No chipset found. Flash detection will most likely fail. <br>
Calibrating delay loop... 491M loops per second, 100 myus = 199 us. OK. <br>Probing for AMD Am29F010A/B, 128 KB: probe_29f040b: id1 0xff, id2 0xff <br>
Probing for AMD Am29F002(N)BB, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for AMD Am29F002(N)BT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff <br>Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0x4e, id2 0x41 <br>
Probing for AMD Am29F080B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x02, id2 0x00, id1 is normal flash content, id2 is normal flash content <br>
Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0x4e, id2 0x41 <br>Probing for AMD Am29LV081B, 1024 KB: probe_29f040b: id1 0x02, id2 0x00 <br>
Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT29C512, 64 KB: probe_jedec: id1 0xee, id2 0xba, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Atmel AT29C010A, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Atmel AT49BV512, 64 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xee, id2 0xba, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Atmel AT49F002(N), 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Atmel AT49F002(N)T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for AMIC A25L40P, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0xff, id2 0xff <br>
Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0xff, id2 0xff <br>Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0x4e, id2 0x41 <br>
Probing for AMIC A49LF040A, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for EMST F49B002UA, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for EON EN29F002(A)(N)B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for EON EN29F002(A)(N)T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Fujitsu MBM29F004BC, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Fujitsu MBM29F004TC, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 <br>Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 <br>
Probing for Intel 28F001BX-B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Intel 28F001BX-T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 <br>Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x02, id2 0x00 <br>
Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Macronix MX29F001B, 128 KB: probe_29f002: id1 0xff, id2 0xff <br>
Probing for Macronix MX29F001T, 128 KB: probe_29f002: id1 0xff, id2 0xff <br>Probing for Macronix MX29F002B, 256 KB: probe_29f002: id1 0xff, id2 0xff <br>
Probing for Macronix MX29F002T, 256 KB: probe_29f002: id1 0xff, id2 0xff <br>Probing for Macronix MX29LV040, 512 KB: probe_29f002: id1 0x4e, id2 0x41 <br>
Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Numonyx M25PE40, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for PMC Pm29F0002T, 256 KB: probe_29f040b: id1 0xff, id2 0xff <br>
Probing for PMC Pm29F0002B, 256 KB: probe_29f040b: id1 0xff, id2 0xff <br>Probing for PMC Pm39LV010, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for PMC Pm49FL002, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for PMC Pm49FL004, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0x02, id2 0x00 <br>Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0x4e, id2 0x41 <br>Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST29EE020A, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0xee, id2 0xba, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST39VF080, 1024 KB: probe_jedec: id1 0x02, id2 0x00, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST49LF002A/B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF003A/B, 384 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF004A/B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x4e, id2 0x41 <br>Probing for SST SST49LF008A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x02, id2 0x00, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0x02, id2 0x00 <br>Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff <br>
Probing for SST SST49LF020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>Probing for SST SST49LF040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x02, id2 0x00, id1 is normal flash content, id2 is normal flash content <br>
Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff <br>Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for ST M29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for ST M29F002T/NT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0x4e, id2 0x41 <br>Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 <br>
Probing for ST M29W010B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for ST M29W040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0x4e, id2 0x41 <br>Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0x4e, id2 0x41 <br>
Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0x02, id2 0x00 <br>Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0x02, id2 0x00 <br>
Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xff, id2 0xff <br>Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff <br>
Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x4e, id2 0x41 <br>Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x02, id2 0x00 <br>
Probing for ST M50LPW116, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SyncMOS S29C31004T, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SyncMOS S29C51001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SyncMOS S29C51002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for SyncMOS S29C51004T, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for TI TMS29F002RB, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for TI TMS29F002RT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content <br>
Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. <br>
Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>
Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>Probing for Winbond W29C011, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>
Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>
Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip.<br>
Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>
Probing for Winbond W39V040C, 512 KB: probe_w39v040c: id1 0x4e, id2 0x41, id1 parity violation<br>Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>
Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0x02, id2 0x00, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W49F002U, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>
Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W49V002FA, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>
Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: id1 0x2, id2 0x0<br>Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: id1 0x4e, id2 0x41<br>Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>
Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>
Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>
Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.<br>No EEPROM/flash device found.<br>If you know which flash chip you have, and if this version of flashrom<br>
supports a similar flash chip, you can try to force read your chip. Run:<br>flashrom -f -r -c similar_supported_flash_chip filename<br><br>Note: flashrom can never write when the flash chip isn't found automatically.<br>
<br>--------------------------<br><br>superiotool -deV<br><br>superiotool r5537 <br>Probing for ALi Super I/O at 0x3f0... <br> Failed. Returned data: id=0xffff, rev=0xff <br>
Probing for ALi Super I/O at 0x370... <br> Failed. Returned data: id=0xffff, rev=0xff <br>Probing for Fintek Super I/O at 0x2e... <br> Failed. Returned data: vid=0xffff, id=0xffff <br>
Probing for Fintek Super I/O at 0x4e... <br> Failed. Returned data: vid=0xffff, id=0xffff <br>Probing for ITE Super I/O (init=standard) at 0x2e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>
Probing for ITE Super I/O (init=it8761e) at 0x2e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>Probing for ITE Super I/O (init=it8228e) at 0x2e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>
Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>Probing for ITE Super I/O (init=standard) at 0x4e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>
Probing for ITE Super I/O (init=it8761e) at 0x4e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>Probing for ITE Super I/O (init=it8228e) at 0x4e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>
Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... <br> Failed. Returned data: id=0xffff, rev=0xf <br>Probing for ITE Super I/O (init=legacy/it8661f) at 0x370...<br> Failed. Returned data: id=0xffff, rev=0xf <br>
Probing for ITE Super I/O (init=legacy/it8671f) at 0x370...<br> Failed. Returned data: id=0xffff, rev=0xf <br>Probing for NSC Super I/O at 0x2e... <br> Failed. Returned data: port=0xff, port+1=0xff <br>
Probing for NSC Super I/O at 0x4e... <br> Failed. Returned data: port=0xff, port+1=0xff <br>Probing for NSC Super I/O at 0x15c... <br> Failed. Returned data: port=0xff, port+1=0xff <br>
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... <br> Failed. Returned data: id=0xff, rev=0xff <br>Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... <br> Failed. Returned data: id=0xff, rev=0xff <br>
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... <br> Failed. Returned data: id=0xff, rev=0xff <br>Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... <br> Failed. Returned data: id=0xff, rev=0xff <br>
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... <br> Failed. Returned data: id=0xff, rev=0xff <br>Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... <br> Failed. Returned data: id=0xff, rev=0xff <br>
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... <br> Failed. Returned data: id=0xff, rev=0xff <br>Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... <br> Failed. Returned data: id=0xff, rev=0xff <br>
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... <br> Failed. Returned data: id=0xff, rev=0xff <br>Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... <br> Failed. Returned data: id=0xff, rev=0xff <br>
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... <br> Failed. Returned data: id=0xff, rev=0xff <br>Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... <br> Failed. Returned data: id=0xff, rev=0xff <br>
Probing for Winbond Super I/O (init=0x88) at 0x2e... <br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff <br>Probing for Winbond Super I/O (init=0x89) at 0x2e... <br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff <br>
Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... <br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff <br>Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... <br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff <br>
Probing for Winbond Super I/O (init=0x88) at 0x4e... <br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x89) at 0x4e...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x88) at 0x3f0...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x89) at 0x3f0...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x88) at 0x370...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x89) at 0x370...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x88) at 0x250...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x89) at 0x250...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...<br> Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff<br>
Probing for VIA Super I/O at 0x3f0...<br> PCI device 1106:0686 not found.<br>No Super I/O found<br><br><br>