<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 12pt;
font-family:Calibri
}
--></style></head>
<body class='hmmessage'><div dir='ltr'>Hi,<br><span id="result_box" class="short_text" lang="en"><span class="hps">I followed</span> <span class="hps">the steps </span></span><span id="result_box" class="short_text" lang="en"><span class="hps">in this</span> <span class="hps">link <a href="http://flashrom.org/Serprog/Arduino_flasher" target="_blank">http://flashrom.org/Serprog/Arduino_flasher</a> for write the SST25LF040A flash chip<br></span></span><br><span id="result_box" class="short_text" lang="en"><span class="hps"><span id="result_box" lang="en"><span class="hps">run first time</span> <span class="hps">and asked to</span> <span class="hps">specify which</span> <span class="hps">chip</span> <span class="hps">was using<br></span></span></span></span><br><span id="result_box" class="short_text" lang="en"><span class="hps"><span id="result_box" lang="en"><span class="hps"><span id="result_box" lang="en"><span class="hps">run</span> <span class="hps">specifying the</span> <span class="hps">chip</span><span>, the error</span> <span class="hps">not</span> <span class="hps">found the</span> <span class="hps">chip<br><br><br></span></span></span></span></span></span><span id="result_box" class="short_text" lang="en"><span class="hps"><span id="result_box" class="short_text" lang="en"><span class="hps">follows</span> <span class="hps">the commands</span> <span class="hps">executed<br><br><br></span></span>hugo@hugo-linux ~/flashrom $ sudo ./flashrom -p serprog:dev=/dev/ttyACM0:2000000<br>flashrom v0.9.6.1-r1701 on Linux 3.5.0-17-generic (i686)<br>flashrom is free software, get the source code at http://www.flashrom.org<br><br>Calibrating delay loop... OK.<br>serprog: Programmer name is "serprog-duino"<br>Found SST flash chip "SST25LF040A" (512 kB, SPI) on serprog.<br>Found SST flash chip "SST25VF040" (512 kB, SPI) on serprog.<br>Multiple flash chips were detected: "SST25LF040A", "SST25VF040"<br>Please specify which chip to use with the -c <chipname> option.<br><br></span></span><br><span id="result_box" class="short_text" lang="en"><span class="hps"><span id="result_box" class="short_text" lang="en"><span class="hps">specified the</span> <span class="hps">chip</span> <span class="hps">and</span> <span class="hps">verbose<br><br></span></span>hugo@hugo-linux ~/flashrom $ sudo ./flashrom -c "SST25LF040A" -V -p serprog:dev=/dev/ttyACM0:2000000<br>flashrom v0.9.6.1-r1701 on Linux 3.5.0-17-generic (i686)<br>flashrom is free software, get the source code at http://www.flashrom.org<br><br>flashrom was built with libpci 3.1.9, GCC 4.7.2, little endian<br>Command line (5 args): ./flashrom -c SST25LF040A -V -p serprog:dev=/dev/ttyACM0:2000000<br>Calibrating delay loop... OS timer resolution is 1 usecs, 1004M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10002 us, 4 myus = 4 us, OK.<br>Initializing serprog programmer<br>Baud rate is 2000000.<br>serprog: connected - attempting to synchronize<br>.....<br>serprog: Synchronized<br>serprog: Interface version ok.<br>serprog: Bus support: parallel=off, LPC=off, FWH=off, SPI=on<br>Warning: Automatic command availability check failed for cmd 0x08 - won't execute cmd<br>Warning: Automatic command availability check failed for cmd 0x11 - won't execute cmd<br>serprog: Programmer name is "serprog-duino"<br>serprog: Serial buffer size is 65535<br>serprog: Warning: Programmer does not support toggling its output drivers<br>The following protocols are supported: SPI.<br>Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x0, id2 0x0<br>No EEPROM/flash device found.<br>Note: flashrom can never write if the flash chip isn't found automatically.<br><br><br><br></span></span><span id="result_box" class="short_text" lang="en"><span class="hps"></span></span> </div></body>
</html>