<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=us-ascii">
<meta name="Generator" content="Microsoft Word 14 (filtered medium)">
<style><!--
/* Font Definitions */
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri","sans-serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Calibri","sans-serif";
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri","sans-serif";}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]-->
</head>
<body lang="EN-US" link="blue" vlink="purple">
<div class="WordSection1">
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">FYI,<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">This is informational only. I can program the ROM. <o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">When programming the N25Q128 from the Raspberry PI, I will get verification errors. If I push it up the hill several times, it will eventually pass. The N25Q128 remains on the target board, I am hold the ARM processor on that board
in RESET. The Raspberry PI is attached via a ribbon cable and 100 ohm series resistors.
<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Since my system is unique, it is entirely possible that this is just an artifact of my setup. However, the message as pasted below, asked me to report it, so I am doing that. I tried both the release and the latest snapshot. Both seem
to operate the same. <o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">I tried three different target boards with the N25Q128 and all operate the same. Verification fails, but if I repeat the programming operation several times, it will pass. Please note the message at the end. The previous program and
verify attempt failed. However, when I tried again, it aborted early because what I was attempting to program into the part already matched the parts contents. AKA, nothing to do. <o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">---- Steve<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">*************************************************************************************************************<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Verifying flash... FAILED at 0x00022f00! Expected=0x61, Found=0xff, failed byte count from 0x00000000-0x00ffffff: 0x100<o:p></o:p></p>
<p class="MsoNormal">Your flash chip is in an unknown state.<o:p></o:p></p>
<p class="MsoNormal">Please report this on IRC at chat.freenode.net (channel #flashrom) or<o:p></o:p></p>
<p class="MsoNormal">mail flashrom@flashrom.org, thanks!<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Verifying flash... FAILED at 0x0001cc92! Expected=0x83, Found=0x9f, failed byte count from 0x00000000-0x00ffffff: 0x68<o:p></o:p></p>
<p class="MsoNormal">Your flash chip is in an unknown state.<o:p></o:p></p>
<p class="MsoNormal">Please report this on IRC at chat.freenode.net (channel #flashrom) or<o:p></o:p></p>
<p class="MsoNormal">mail flashrom@flashrom.org, thanks!<o:p></o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal"><o:p> </o:p></p>
<p class="MsoNormal">Warning: Chip content is identical to the requested image.<o:p></o:p></p>
<p class="MsoNormal">Erase/write done.<o:p></o:p></p>
</div>
</body>
</html>