flashrom v0.9.8-r1888 on Linux 3.19.0-56-generic (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.1.7, GCC 4.4.6 20120305 (Red Hat 4.4.6-4), little endian
Command line (7 args): ./flashrom -p internal:laptop=force_I_want_a_brick -c N25Q128..3E -w bios.bin -V
Calibrating delay loop... OS timer resolution is 1 usecs, 707M loops per second, 10 myus = 10 us, 100 myus = 98 us, 1000 myus = 1003 us, 10000 myus = 10570 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
DMI string chassis-type: "Laptop"
Laptop detected via DMI.
DMI string system-manufacturer: "N/A"
DMI string system-product-name: "N/A"
DMI string system-version: "N/A"
DMI string baseboard-manufacturer: "Kontron Europe GmbH"
DMI string baseboard-product-name: "COMe-bHL6RXT"
DMI string baseboard-version: "1.0.1"
Found chipset "Intel QM87" with PCI ID 8086:8c4f.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap: not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytes
SPI Read Configuration: prefetching enabled, caching enabled, 
BIOS_CNTL = 0x09: BIOS Lock Enable: disabled, BIOS Write Enable: enabled
SPIBAR = 0x00007fd164269000 + 0x3800
0x04: 0x6009 (HSFS)
HSFS: FDONE=1, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0
Programming OPCODES... done
0x06: 0x0004 (HSFC)
HSFC: FGO=0, FCYCLE=2, FDBC=0, SME=0
0x50: 0x0000ffff (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff
0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-write.
0x58: 0x0fff0a00 FREG1: BIOS region (0x00a00000-0x00ffffff) is read-write.
0x5C: 0x09ff0003 FREG2: Management Engine region (0x00003000-0x009fffff) is read-write.
0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write.
0x90: 0xc4 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0xf84260 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=6, DBC=2, SME=0, SCF=0
0x94: 0x5006     (PREOP)
0x96: 0x463b     (OPTYPE)
0x98: 0x05d80302 (OPMENU)
0x9C: 0xc79f0190 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x80802005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xD0: 0x50444653 (FPB)
OK.
The following protocols are supported: FWH, SPI.
Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4018
No EEPROM/flash device found.
Note: flashrom can never write if the flash chip isn't found automatically.
Restoring MMIO space at 0x7fd16426c8a0
Restoring MMIO space at 0x7fd16426c89c
Restoring MMIO space at 0x7fd16426c898
Restoring MMIO space at 0x7fd16426c896
Restoring MMIO space at 0x7fd16426c894
Restoring PCI config space for 00:1f:0 reg 0xdc