<div dir="ltr">*Flash chip is Atmel 26DF081A, I'm finding that I can't read it in-circuit either, with a TL866A programmer and clip.<br><div><br>flashrom v0.9.7-r1782 on Linux 3.16.0-4-586 (i686)<br>flashrom is free software, get the source code at <a href="http://www.flashrom.org">http://www.flashrom.org</a><br><br>flashrom was built with libpci 3.2.1, GCC 4.8.2, little endian<br>Command line (3 args): flashrom -p internal -V<br>Calibrating delay loop... OS timer resolution is 1 usecs, 2386M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 14067 us, 4 myus = 4 us, OK.<br>Initializing internal programmer<br>No coreboot table found.<br>Using Internal DMI decoder.<br>DMI string chassis-type: "Desktop"<br>DMI string system-manufacturer: "                                "<br>DMI string system-product-name: "                                "<br>DMI string system-version: "                        "<br>DMI string baseboard-manufacturer: "Intel Corporation"<br>DMI string baseboard-product-name: "DG965SS"<br>DMI string baseboard-version: "AAD41678-308"<br>W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect.<br>Active config mode, unknown reg 0x20 ID: f1.<br>Please send the output of "flashrom -V" to <br><a href="mailto:flashrom@flashrom.org">flashrom@flashrom.org</a> with W836xx: your board name: flashrom -V<br>as the subject to help us finish support for your Super I/O. Thanks.<br>Found chipset "Intel ICH8/ICH8R" with PCI ID 8086:2810. Enabling flash write... Root Complex Register Block address = 0xfed1c000<br>GCS = 0x400464: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI)<br>Top Swap : not enabled<br><br>0xfff80000/0xffb80000 FWH IDSEL: 0x0<br>0xfff00000/0xffb00000 FWH IDSEL: 0x0<br>0xffe80000/0xffa80000 FWH IDSEL: 0x1<br>0xffe00000/0xffa00000 FWH IDSEL: 0x1<br>0xffd80000/0xff980000 FWH IDSEL: 0x2<br>0xffd00000/0xff900000 FWH IDSEL: 0x2<br>0xffc80000/0xff880000 FWH IDSEL: 0x3<br>0xffc00000/0xff800000 FWH IDSEL: 0x3<br>0xff700000/0xff300000 FWH IDSEL: 0x4<br>0xff600000/0xff200000 FWH IDSEL: 0x5<br>0xff500000/0xff100000 FWH IDSEL: 0x6<br>0xff400000/0xff000000 FWH IDSEL: 0x7<br>0xfff80000/0xffb80000 FWH decode enabled<br>0xfff00000/0xffb00000 FWH decode enabled<br>0xffe80000/0xffa80000 FWH decode disabled<br>0xffe00000/0xffa00000 FWH decode disabled<br>0xffd80000/0xff980000 FWH decode disabled<br>0xffd00000/0xff900000 FWH decode disabled<br>0xffc80000/0xff880000 FWH decode disabled<br>0xffc00000/0xff800000 FWH decode disabled<br>0xff700000/0xff300000 FWH decode disabled<br>0xff600000/0xff200000 FWH decode disabled<br>0xff500000/0xff100000 FWH decode disabled<br>0xff400000/0xff000000 FWH decode disabled<br>Maximum FWH chip size: 0x100000 bytesSPI Read Configuration: prefetching disabled, caching enabled, <br>BIOS_CNTL = 0x02: BIOS Lock Enable: enabled, BIOS Write Enable: disabled<br>Warning: Setting Bios Control at 0xdc from 0x02 to 0x01 failed.<br>New value is 0x02.<br>SPIBAR = 0xb77be000 + 0x3020<br>0x04: 0xe008 (HSFS)<br>HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1<br>Warning: SPI Configuration Lockdown activated.<br>Reading OPCODES... done<br>0x06: 0x3f00 (HSFC)<br>HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0<br>0x50: 0x00000a0b (FRAP)<br>BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b<br>0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only.<br>0x58: 0x00ff0035 FREG1: BIOS region (0x00035000-0x000fffff) is read-write.<br>0x5C: 0x00340003 FREG2: Warning: Management Engine region (0x00003000-0x00034fff) is locked.<br>0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write.<br>Not all flash regions are freely accessible by flashrom. This is most likely<br>due to an active ME. Please see <a href="http://flashrom.org/ME">http://flashrom.org/ME</a> for details.<br>Writes have been disabled for safety reasons. You can enforce write<br>support with the ich_spi_force programmer option, but you will most likely<br>harm your hardware! If you force flashrom you will get no support if<br>something breaks. On a few mainboards it is possible to enable write<br>access by setting a jumper (see its documentation or the board itself).<br>0x90: 0x00 (SSFS)<br>SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0<br>0x91: 0x004024 (SSFC)<br>SSFC: SCGO=0, ACS=1, SPOP=0, COP=2, DBC=0, SME=0, SCF=0<br>0x94: 0x0000     (PREOP)<br>0x96: 0x0008     (OPTYPE)<br>0x98: 0x0000ab9f (OPMENU)<br>0x9C: 0x00000000 (OPMENU+4)<br>0xC1: 0xffffffff (VSCC)<br>VSCC: BES=0x3, WG=1, WSR=1, WEWS=1, EO=0xff, VCL=1<br><br>Enabling hardware sequencing because some important opcode is locked.<br>PROBLEMS, continuing anyway<br>The following protocols are supported: FWH, Programmer-specific.<br>Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip with a density of 1024 kB.<br>There is only one partition containing the whole address space (0x000000 - 0x0fffff).<br>There are 256 erase blocks with 4096 B each.<br>Found Programmer flash chip "Opaque flash chip" (1024 kB, Programmer-specific) at physical address 0x0.<br>Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x77, id2 0x8e, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x77, id2 0x8e, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x77, id2 0x8e, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x60, id2 0x7c, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x77, id2 0x8e, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x77, id2 0x8e, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x14, id2 0xa0, id1 parity violation, id1 is normal flash content, id2 is normal flash content<br>Found Programmer flash chip "Opaque flash chip" (1024 kB, Programmer-specific).<br>No operations were specified.<br>Restoring PCI config space for 00:1f:0 reg 0xdc<br><br></div></div>