source: trunk/util/z60_flashrom.rules @ 1453

Revision 1453, 3.1 KB checked in by uwe, 7 months ago (diff)

Add support for the GOEPEL PicoTAP programmer.

 http://www.goepel.com/en/jtagboundary-scan/hardware/picotap.html

This device is actually a JTAG adapter, but since it uses standard
FT2232 A interface pins, it can be easily used as SPI programmer
(tested it here successfully). PicoTAP supports only 5V output, so one
needs to reduce this to 3.3V in a same manner as DLP Design DLP-USB1232H, see

 http://flashrom.org/FT2232SPI_Programmer#DLP_Design_DLP-USB1232H

for details.

The PicoTAP pin-out is as follows:

PicoTAP | SPI

---------+-------

TCK | SCLK
TMS | CS#
TDI | SO
TDO | SI

/TRST | -

GND | GND
+5V | VCC, HOLD# & WP# after 3.3V regulator

I managed to run PicoTAP in 10MHz, 15MHz and 30MHz modes (by forcing
DIVIDE_BY), against SST25VF016B SPI flash, read/write/erase all worked
fine (write seems somewhat slow).

Signed-off-by: Samir Ibradžić <sibradzic@…>
Acked-by: Uwe Hermann <uwe@…>

Line 
1##
2## This file is part of the flashrom project.
3##
4## Copyright (C) 2010 Uwe Hermann <uwe@hermann-uwe.de>
5##
6## This program is free software; you can redistribute it and/or modify
7## it under the terms of the GNU General Public License as published by
8## the Free Software Foundation; either version 2 of the License, or
9## (at your option) any later version.
10##
11## This program is distributed in the hope that it will be useful,
12## but WITHOUT ANY WARRANTY; without even the implied warranty of
13## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
14## GNU General Public License for more details.
15##
16## You should have received a copy of the GNU General Public License
17## along with this program; if not, write to the Free Software
18## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
19##
20
21##
22## Please keep this list sorted alphabetically by vendor/device name.
23##
24
25##
26## This is tested on udev version 154, other versions may need small fixes.
27##
28## Note that you might want to change the "plugdev" group to whatever is
29## suitable for your respective distribution.
30##
31
32ACTION!="add|change", GOTO="flashrom_rules_end"
33SUBSYSTEM!="usb|usb_device", GOTO="flashrom_rules_end"
34
35# Amontec JTAGkey(2)
36# http://www.amontec.com/jtagkey.shtml
37ATTRS{idVendor}=="0403", ATTRS{idProduct}=="cff8", MODE="664", GROUP="plugdev"
38
39# Buspirate
40# http://dangerousprototypes.com/2009/10/08/bus-pirate-raw-spi-mode/
41ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", MODE="664", GROUP="plugdev"
42
43# Dediprog SF100
44# http://www.dediprog.com/SPI-flash-in-circuit-programming/SF100
45ATTRS{idVendor}=="0483", ATTRS{idProduct}=="dada", MODE="664", GROUP="plugdev"
46
47# DLP Design DLP-USB1232H
48# http://www.dlpdesign.com/usb/usb1232h.shtml
49ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6010", MODE="664", GROUP="plugdev"
50
51# FIC OpenMoko Neo1973 Debug board (V2+)
52# http://wiki.openmoko.org/wiki/Neo1973_Debug_Board_v2
53ATTRS{idVendor}=="1457", ATTRS{idProduct}=="5118", MODE="664", GROUP="plugdev"
54
55# FTDI FT4232H Mini-Module
56# http://www.ftdichip.com/Products/EvaluationKits/FT4232H_MiniModule.htm
57ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6011", MODE="664", GROUP="plugdev"
58
59# GOEPEL PicoTAP
60# http://www.goepel.com/jtagboundary-scan/hardware/picotap.html
61ATTRS{idVendor}=="096c", ATTRS{idProduct}=="1449", MODE="664", GROUP="plugdev"
62
63# Olimex ARM-USB-OCD
64# http://olimex.com/dev/arm-usb-ocd.html
65ATTRS{idVendor}=="15ba", ATTRS{idProduct}=="0003", MODE="664", GROUP="plugdev"
66
67# Olimex ARM-USB-OCD-H
68# http://olimex.com/dev/arm-usb-ocd-h.html
69ATTRS{idVendor}=="15ba", ATTRS{idProduct}=="002b", MODE="664", GROUP="plugdev"
70
71# Olimex ARM-USB-TINY
72# http://olimex.com/dev/arm-usb-tiny.html
73ATTRS{idVendor}=="15ba", ATTRS{idProduct}=="0004", MODE="664", GROUP="plugdev"
74
75# Olimex ARM-USB-TINY-H
76# http://olimex.com/dev/arm-usb-tiny-h.html
77ATTRS{idVendor}=="15ba", ATTRS{idProduct}=="002a", MODE="664", GROUP="plugdev"
78
79# TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA)
80# http://www.diygadget.com/tiao-usb-multi-protocol-adapter-jtag-spi-i2c-serial.html
81ATTRS{idVendor}=="0403", ATTRS{idProduct}=="8a98", MODE="664", GROUP="plugdev"
82
83LABEL="flashrom_rules_end"
Note: See TracBrowser for help on using the repository browser.