You probably came here trying to find a small (minutes to hours) and easy task where you can get your hands dirty and get results immediately.
If you're a flashrom newbie, this page is for you.
- 1 Open tasks
- 1.1 Find chips without voltage data
- 1.2 Find boards that have a board enable but are not mentioned in print.c
- 1.3 Add timing info to flash chip definitions (mostly done)
- 1.4 Add new flash chip definitions
- 1.5 Test flashrom
- 1.6 Add support for multiple slaves to the ft2232_spi programmer
- 1.7 Replace programmer_delay() with internal_sleep() where appropriate
- 2 Done
Find chips without voltage data
We have added allowed supply voltage ranges (usually denoted VCC in datasheets) to the chip definitions in flashchips.c, but not all of them. Complete the list by looking for the right datasheet and editing flashchips.c accordingly.
Find boards that have a board enable but are not mentioned in print.c
There may be a few boards that had a Board Enable added (in board_enable.c) but which were not added to the array named boards_known in print.c (usually by mistake).
Find those and send a list or even a patch for print.c to the mailing list.
Even better would be an automatic detection of such mistakes. We already do some sanity checks on startup (cf. selfcheck() in flashrom.c).
Add timing info to flash chip definitions (mostly done)
Go through the list of flash chips in flashchips.c inside the flashrom source. For each chip (except SPI chips), read through the data sheets and add a comment to the flash chip definition which contains the timing information in microseconds(!) for the probe sequence.
This will make probing a lot more reliable.
Every annotated chip helps.
Add new flash chip definitions
We have a few dozen chip IDs listed in flash.h, but not in flashchips.c. You can find them by running util/list_yet_unsupported_chips.sh. Then dig up the data sheets and add chip definitions for them to flashchips.c. You can use similar flash chips as a guideline. Check our list of pending patches (http://patchwork.coreboot.org/project/flashrom/list/) to not duplicate someone's work. Reviewing any pending patches by verifying the values in the patches is of course also very welcomed too! The process of adding a chip and the needed data structures are explained here.
This will reduce the number of undetected chips and every added chip broadens flashrom support.
Add (ferroelectric) SPI chips made by Ramtron
Please see the Board Testing HOWTO.
Add support for multiple slaves to the ft2232_spi programmer
The FT232H for example has 4 generic GPIO pins that could be used as additional CS pins. Think about useful command line arguments (what about other programmers that support similar functionality, e.g. by supporting multiple CS pins natively?) before you start. An example how this could look like exists already.
Replace programmer_delay() with internal_sleep() where appropriate
If a delay call does not depend on precise timing and if the programmer in question does not offer its own delay function, programmer_delay() can be replaced with internal_sleep(). If a delay call does not depend on precise timing and if the delay should run on the host, programmer_delay() can be replaced with internal_sleep().
Add automatic uploading of log files
We have a pastebin at http://paste.flashrom.org. Create a patch that (if enabled) automatically uploads the output of a flashrom run to it using libcurl or a similar library (free license, cross-platform).
PoC sent by Michael Coppola, but so far rejected by Carl-Daniel.
Tag SPI chips in flashchips.c with the status register write command according to their datasheets
Usually the status register of SPI chips is write protected and has to be made accessible by one of two possible commands (or by either one). We indicate this by setting 2 bits in the feature flags of the chip definition in flashchips.c. The default is EWSR (see spi_write_status_register in spi25.c) and so no chips needing this have been tagged correctly (yet!). The task is to look at all chip definitions with bustype = BUS_SPI and check the feature_bits field if it contains the correct FEATURE_WRSR_* flag and add/change it after looking it up in the datasheet. In case either works use FEATURE_WRSR_EITHER. Please send a list of chips to change together with the correct flag or (preferably) a patch to the mailing list.
Patch created by Steven Zakulec, committed in r1527.