FT2232SPI Programmer: Difference between revisions

From flashrom
Jump to navigation Jump to search
(→‎Setup: Explain schematics and how to build the breadboard circuit.)
Line 34: Line 34:


<gallery>
<gallery>
File:Dlp usb1232h top.jpg
File:Dlp usb1232h side.jpg
File:Dlp usb1232h side.jpg
File:Dlp usb1232h bottom.jpg
File:Dlp usb1232h bottom.jpg
Line 40: Line 39:
File:Via epia m700 programer.jpg
File:Via epia m700 programer.jpg
File:Ft2232spi programer.jpg
File:Ft2232spi programer.jpg
File:Dlp usb1232h spi programmer breadboard 1.jpg
File:Dlp usb1232h spi programmer breadboard 2.jpg
</gallery>
</gallery>



Revision as of 21:28, 5 September 2009

Recent versions of flashrom support the -p ft2232spi option which allows you to use a FTDI FT2232H/FT4232H based device as external SPI programmer.

This is made possible by using libftdi. flashrom autodetects the presence of libftdi headers and enables FT2232H/FT4232H support if they are available.

DLP Design DLP-USB1232H

The DLP Design DLP-USB1232H (datasheet) can be used with flashrom for programming SPI chips.

Where to buy: Digikey, Mouser, Saelig

Setup

DLP-USB1232H based SPI programmer schematics

In order to use the DLP-USB1232H device as SPI programmer you have to setup a small circuit (e.g. on a breadboard). See the schematics for details (you can also download the schematics as PDF for easier printing).

  • You must connect/shorten pins 8 and 9, which configures the device to be powered by USB. Without this connection it will not be powered, and thus not be detected by your OS (e.g. it will not appear in the lsusb output).
  • You need a 3.3V voltage regulator to convert the 5V from USB to 3.3V, so you can power the 3.3V SPI BIOS chip.
    • You can probably use pretty much any 3.3V voltage regulator, e.g. LD33V or LD1117xx. For usage on a breadboard the TO-220 packaging is probably most useful.
    • You have to connect two capacitors (e.g. 100nF and 10uF as per datasheets, but using two 10uF capacitors, or even two 47uF capacitors also works in practice) as shown in the schematics, otherwise the voltage regulator will not work correctly and reliably.
  • Connect the following pins from the DLP-USB1232H to the SPI BIOS chip:
    • 18 (SK) to SCLK
    • 16 (DO) to SI
    • 2 (DI) to SO
    • 5 (CS) to CS#
    • The WP# and HOLD# pins should be tied to VCC! If you leave them unconnected you'll likely experience strange issues.
    • All GND pins should be connected together (pins 1 and 10 on the DLP-USB1232H, pin 8 on the SPI chip, pin 1 on the voltage regulator).

You have to invoke flashrom with the following parameters:

$ flashrom -p ft2232spi:ft2232_type=2232:port=A

Photos

FTDI FT2232H Mini-Module

The FTDI FT2232H Mini-Module Evaluation Kit (datasheet) can be used with flashrom for programming SPI chips.

Where to buy: FTDI

FTDI FT4232H Mini-Module

The FTDI FT4232H Mini-Module Evaluation Kit (datasheet) can be used with flashrom for programming SPI chips.

Where to buy: FTDI