[flashrom] Flashing of ASUS M2N4-SLI BIOS
Michael Stephenson
mickstephenson at googlemail.com
Sun Oct 25 16:28:22 CET 2009
Hi,
My motherboard is an ASUS M2N4-SLI, and I attempted to flash it with the
1205 BIOS available from the ASUS website, the flash went without
incident as can be seen here http://www.pastebin.ca/1642685
When I rebooted everything seemed to work fine until I reached GDM where
I found my usb mouse no longer worked, so I dropped to console
(fortunately am using a PS/2 keyboard) where I discovered my ethernet
card had not been discovered, after rebooting a few times and tinkering
with the BIOS to no effect I decided to restore my backup. Where
everything worked fine again.
Speaking to Carldani in irc he made the comments:
> carldani: they store the ethernet address in the bios image, so if you reflash, you lose the ethernet address...
> carldani: if you have a hex editor, you could try to locate your mac address in the backup file
> carldani: the mac address may be stored in reverse...
> carldani: maybe someone on the mailing list knows the mac extraction procedure better than I do
I have attached the output of lspci -nnvvvxxx and flashrom -V
Thanks
Michael
-------------- next part --------------
00:00.0 Memory controller [0580]: nVidia Corporation CK804 Memory Controller [10de:005e] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00: de 10 5e 00 06 00 b0 00 a3 00 80 05 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 00 00
00:01.0 ISA bridge [0601]: nVidia Corporation CK804 ISA Bridge [10de:0050] (rev f3)
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00: de 10 50 00 0f 00 a0 00 f3 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 5a 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
00:01.1 SMBus [0c05]: nVidia Corporation CK804 SMBus [10de:0052] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: I/O ports at fc00 [size=32]
Region 4: I/O ports at 4c00 [size=64]
Region 5: I/O ports at 4c40 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00: de 10 52 00 01 00 b0 00 a2 00 05 0c 00 00 80 00
10: 01 fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 4c 00 00 41 4c 00 00 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 01 03 01
00:02.0 USB Controller [0c03]: nVidia Corporation CK804 USB Controller [10de:005a] (rev a2) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00: de 10 5a 00 07 00 b0 00 a2 10 03 0c 00 00 80 00
10: 00 f0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 01 03 01
00:02.1 USB Controller [0c03]: nVidia Corporation CK804 USB Controller [10de:005b] (rev a3) (prog-if 20)
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00: de 10 5b 00 06 00 b0 00 a3 20 03 0c 00 00 80 00
10: 00 00 b0 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 02 03 01
00:04.0 Multimedia audio controller [0401]: nVidia Corporation CK804 AC'97 Audio Controller [10de:0059] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:822c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at f000 [size=256]
Region 1: I/O ports at ec00 [size=256]
Region 2: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00: de 10 59 00 07 00 b0 00 a2 00 01 04 00 00 00 00
10: 01 f0 00 00 01 ec 00 00 00 d0 02 fe 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 2c 82
30: 00 00 00 00 44 00 00 00 00 00 00 00 03 01 02 05
00:06.0 IDE interface [0101]: nVidia Corporation CK804 IDE [10de:0053] (rev f2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at e800 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
00: de 10 53 00 05 00 b0 00 f2 8a 01 01 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 03 01
00:07.0 IDE interface [0101]: nVidia Corporation CK804 Serial ATA Controller [10de:0054] (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00: de 10 54 00 07 00 b0 00 f3 85 01 01 00 00 00 00
10: f1 09 00 00 f1 0b 00 00 71 09 00 00 71 0b 00 00
20: 01 d4 00 00 00 c0 02 fe 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 03 01
00:08.0 IDE interface [0101]: nVidia Corporation CK804 Serial ATA Controller [10de:0055] (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at c000 [size=16]
Region 5: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00: de 10 55 00 07 00 b0 00 f3 85 01 01 00 00 00 00
10: e1 09 00 00 e1 0b 00 00 61 09 00 00 61 0b 00 00
20: 01 c0 00 00 00 b0 02 fe 00 00 00 00 43 10 5a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 03 01
00:09.0 PCI bridge [0604]: nVidia Corporation CK804 PCI Bridge [10de:005c] (rev f2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=128
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fdf00000-fdffffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00: de 10 5c 00 07 00 a0 00 f2 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 80 a0 a0 80 22
20: f0 fd f0 fd f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 04 02
00:0a.0 Bridge [0680]: nVidia Corporation CK804 Ethernet Controller [10de:0057] (rev f3)
Subsystem: ASUSTeK Computer Inc. Device [1043:812a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at bc00 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00: de 10 57 00 07 00 b8 00 f3 00 80 06 00 00 00 00
10: 00 a0 02 fe 01 bc 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 2a 81
30: 00 00 00 00 44 00 00 00 00 00 00 00 03 01 01 14
00:0b.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev f3)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 40000000-400fffff
Prefetchable memory behind bridge: 0000000040100000-00000000401fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00: de 10 5d 00 07 04 10 00 f3 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 11 11 00 20
20: 00 40 00 40 11 40 11 40 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00
00:0c.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev f3)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00: de 10 5d 00 04 04 10 00 f3 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00
00:0d.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev f3)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00: de 10 5d 00 04 04 10 00 f3 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 04 04 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00
00:0e.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev a3)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fa000000-fcffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00: de 10 5d 00 07 04 10 00 a3 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 05 05 00 91 91 00 00
20: 00 fa f0 fc 01 d0 f1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 0c 00
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: amd64_edac_mod
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp
00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00
01:06.0 Communication controller [0780]: Conexant Systems, Inc. HSF 56k HSFi Modem [14f1:2f00] (rev 01)
Subsystem: GVC Corporation Device [13e0:8d85]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 255
Region 0: Memory at fdff0000 (32-bit, non-prefetchable) [size=64K]
Region 1: I/O ports at ac00 [size=8]
Capabilities: <access denied>
00: f1 14 00 2f 07 00 90 02 01 00 80 07 00 20 00 00
10: 00 00 ff fd 01 ac 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e0 13 85 8d
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 01 00 00
02:00.0 SATA controller [0106]: JMicron Technology Corp. JMB362/JMB363 AHCI Controller [197b:2363] (rev 02) (prog-if 01)
Subsystem: JMicron Technology Corp. JMB362/JMB363 AHCI Controller [197b:2363]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=8K]
[virtual] Expansion ROM at 40100000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
00: 7b 19 63 23 06 00 10 00 02 01 06 01 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 40 00 00 00 00 7b 19 63 23
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 01 00 00
02:00.1 IDE interface [0101]: JMicron Technology Corp. JMB362/JMB363 AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: JMicron Technology Corp. JMB362/JMB363 AHCI Controller [197b:2363]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 1010 [size=8]
Region 1: I/O ports at 1020 [size=4]
Region 2: I/O ports at 1018 [size=8]
Region 3: I/O ports at 1024 [size=4]
Region 4: I/O ports at 1000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
00: 7b 19 63 23 05 00 10 00 02 85 01 01 00 00 00 00
10: 11 10 00 00 21 10 00 00 19 10 00 00 25 10 00 00
20: 01 10 00 00 00 00 00 00 00 00 00 00 7b 19 63 23
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 02 00 00
05:00.0 VGA compatible controller [0300]: nVidia Corporation G73 [GeForce 7600 GT] [10de:0391] (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 9c00 [size=128]
[virtual] Expansion ROM at fcfe0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
00: de 10 91 03 07 00 10 00 a1 00 00 03 00 00 00 00
10: 00 00 00 fa 0c 00 00 d0 00 00 00 00 04 00 00 fb
20: 00 00 00 00 01 9c 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 00 00
-------------- next part --------------
flashrom v0.9.1-r706
No coreboot table found.
Found chipset "NVIDIA CK804", enabling flash write... OK.
This chipset supports the following protocols: Non-SPI.
Calibrating delay loop... 609M loops per second, 100 myus = 194 us. OK.
Probing for AMD Am29F010A/B, 128 KB: probe_29f040b: id1 0x00, id2 0xff
Probing for AMD Am29F002(N)BB, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for AMD Am29F002(N)BT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff
Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0x21, id2 0xba
Probing for AMD Am29F080B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0x21, id2 0xba
Probing for AMD Am29LV081B, 1024 KB: probe_29f040b: id1 0xff, id2 0xff
Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT29C512, 64 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT29C010A, 128 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Atmel AT49BV512, 64 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT49F002(N), 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Atmel AT49F002(N)T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for AMIC A25L40P, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0x21, id2 0xba
Probing for AMIC A49LF040A, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for EMST F49B002UA, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for EON EN29F002(A)(N)B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for EON EN29F002(A)(N)T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Fujitsu MBM29F004BC, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Fujitsu MBM29F004TC, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x21, id2 0x2d
Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x21, id2 0x2d
Probing for Intel 28F001BX-B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Intel 28F001BX-T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x21, id2 0xba
Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff
Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix MX29F001B, 128 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for Macronix MX29F001T, 128 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for Macronix MX29F002B, 256 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for Macronix MX29F002T, 256 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for Macronix MX29LV040, 512 KB: probe_29f002: id1 0xbf, id2 0x50
Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Numonyx M25PE40, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC Pm29F0002T, 256 KB: probe_29f040b: id1 0x5c, id2 0xee
Probing for PMC Pm29F0002B, 256 KB: probe_29f040b: id1 0x5c, id2 0xee
Probing for PMC Pm39LV010, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for PMC Pm49FL002, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for PMC Pm49FL004, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0xff, id2 0xff
Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0x21, id2 0xba
Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST29EE020A, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST39VF080, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST49LF003A/B, 384 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST49LF004A/B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x21, id2 0xba
Probing for SST SST49LF008A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff
Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff
Probing for SST SST49LF020, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for SST SST49LF040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Lock status for 0x000000 (size 0x010000) is 01, write locked
Lock status for 0x010000 (size 0x010000) is 01, write locked
Lock status for 0x020000 (size 0x010000) is 01, write locked
Lock status for 0x030000 (size 0x010000) is 01, write locked
Lock status for 0x040000 (size 0x010000) is 01, write locked
Lock status for 0x050000 (size 0x010000) is 01, write locked
Lock status for 0x060000 (size 0x010000) is 01, write locked
Lock status for 0x070000 (size 0x010000) is 01, write locked
Found chip "SST SST49LF040B" (512 KB, LPC) at physical address 0xfff80000.
Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff
Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST M29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for ST M29F002T/NT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0x21, id2 0xba
Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x21, id2 0x2d
Probing for ST M29W010B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for ST M29W040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0xbf, id2 0x50
Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0xbf, id2 0x50
Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff
Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff
Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0x5c, id2 0xee
Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff
Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x21, id2 0xba
Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff
Probing for ST M50LPW116, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SyncMOS S29C31004T, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SyncMOS S29C51001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SyncMOS S29C51002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for SyncMOS S29C51004T, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for TI TMS29F002RB, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for TI TMS29F002RT, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Winbond W29C011, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip.
Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W39V040C, 512 KB: probe_w39v040c: id1 0xbf, id2 0x50
Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49F002U, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W49V002FA, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec: id1 0xbf, id2 0x50
Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: id1 0xff, id2 0xff
Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: id1 0xbf, id2 0x50
Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible.
No operations were specified.
More information about the flashrom
mailing list